資料來源:https://www.seeedstudio.com/Laser-Engraver-Upgrade-Pack-for-XY-Plotter-Robot-Kit-V2.0-p-2166.html
Introduction:
Laser Engraver Upgrade Pack is for XY Plotter Robot Kit V2.0, it can engrave by laser.
Note: The higher output power of the laser, the better processing capacity it is.
The 500mW laser engraver can do better engraving and cutting ability, it takes less time and more efficient than the 250mW laser engraving.
Follow the instruction, assembly the lasers elements to the assembled XY Plotter Robot Kit V2.0 and upload the firmware to the Me Baseboard. You can use Benbox Laser Engraver to control the laser engraver robot to engrave fabulous artworks.
For reference video as below: (https://www.youtube.com/watch?v=Y2Hj5XXX_hc).
Wavelength γ= 405nm Blue-Violet Laser 450~500mW semiconductor diode lasers elements
Working area: 300mm×350mm
Engrave accuracy:0.1mm
Suggested material:
(1) suggested engrave material: wood board, colorful paper cards, dark opaque acrylic, etc.
(2) suggested cutter material: colorful paper cards, foam papers, etc.
Usage:
For the places required engraving or cutter such as families, hacker spaces, schools, companies, etc.
Minimum age: 18 ages. Under the age of 18, please use under the care of their parents
Security:
Pay attention when you’re operating the blue-violet laser MAKE SURE you’re wearing the goggles to avoid the dangers.
Specification:
Frame: Anodized aluminum
Physical Dimensions(L×W×H): 620mm × 620mm×140mm
Engrave materials: Wood boards, colorful paper cards, dark opaque acrylic, foam papers, etc.
Cutting materials: Colorful paper cards, foam papers, etc.
Working area (X×Y): 300mm×350mm
XY Resolution: 0.1mm
Max Speed: 50mm/s
Power: 100-240 V~50/60Hz AC/DC Power adapter, 12V/2.0A
Software:Benbox Laser Engraver
Supports file type: JPG,PNG,BMP,GIF,DXF
Connections: USB
Electronics: Makeblock Me_baseboard
Resources Download
Dimensions | 285mm x 130mm x 80mm |
Weight | G.W 717g |
Battery | Exclude |
Bracket 3x6 | 1 |
HEX Screwdriver 2.5mm | 1 |
Cross Screwdriver 3mm | 1 |
Socket Cap Screw M4x8-Botton Head | 4 |
Countersunk Screw M3x8 | 4 |
Nylon Cable Ties | 5 |
Motor Cable Jeck plug | 1 |
450-500mW blue-violet Laser Components | 1 |
DC power cord 5.5*2.1MM | 1 |
Foot pads | 4 |
介紹:
鐳射雕刻機升級包是為 XY 繪圖器機器人套件 V2.0, 它可以刻鐳射。
注意:雷射器的輸出功率越大, 處理能力就越好。
500mW 鐳射雕刻機能更好的雕刻和切割能力, 它需要比250mW 鐳射雕刻更少的時間和效率。
按照指示, 組裝鐳射元件到組裝的 XY 繪圖器機器人套件 V2.0, 並上傳固件到我的底板。您可以使用Benbox 鐳射雕刻機控制鐳射雕刻機器人雕刻神話般的藝術品。
如下所示的參考視頻: (HTTPs://www.youtube.com/watch?v=Y2Hj5XXX_hc)。
波長γ = 405nm 藍紫光雷射器 450 ~ 500 兆瓦半導體雷射器元件
工作區域: 300mm×350mm
雕刻精度: 0.1mm
推薦材料:
(1) 推薦的雕刻材料: 木板、彩色紙卡、暗不透明亞克力等。
(2) 推薦刀具材質: 彩色紙卡、發泡紙張等。
使用:
對於需要雕刻或切割的地方, 如家庭、駭客空間、學校、公司等。
最低年齡:18 歲。在18歲以下, 請在父母的照顧下使用
安全:
當你在操作藍紫色雷射器時要注意, 確保你戴著護目鏡, 以避免危險。
規範:
框架: 陽極氧化鋁
物理尺寸 (尺寸): 620mm x 620mm×140mm
雕刻材料: 木板、彩色紙卡、暗不透明亞克力、發泡紙等。
切割材料: 彩色紙卡, 泡沫紙張等。
工作區 (X×Y): 300mm×350mm
XY 解析度: 0.1mm
最大轉速:50 毫米/秒
電源: 100-240 V~50/60Hz 交流/直流電源配接器, 12 伏/2.0A
軟體:Benbox 鐳射雕刻機
支援檔案類型: JPG、PNG、BMP、GIF、DXF
連接: USB
電子產品: Makeblock Me_baseboard
資源下載
尺寸 | 285mm x 130mm x 80mm |
重量 | G. W 717g |
電池 | 排除 |
支架3x6 | 1 |
六角螺絲刀2.5mm | 1 |
十字螺絲刀3mm | 1 |
插座帽螺絲 M4x8-Botton 頭 | 4 |
埋頭螺絲 M3x8 | 4 |
尼龍紮帶 | 5 |
電機電纜 Jeck 插頭 | 1 |
450-500mW 藍紫鐳射元件 | 1 |
直流電源線 5.5 * 2.1MM | 1 |
腳墊 | 4 |