資料來源:https://www.seeedstudio.com/DSO-Shell-DIY-Kit-p-2929.html
The DSO Shell is a DIY kit for the 0-200 KHz bandwidth DSO oscilloscope. It is a perfect kit for the makers in your life!
The display and MCU are now mounted on the same board (mainboard) to avoid using inter-board pin-headers. Feedback from DSO138 users have shown that soldering on the pin-headers are often problematic for many beginners. The analog channel is placed on a separated board which contains most of the components that need to be soldered on. This brings in better separation between the analog and digital circuits. Without the analog portion, the mainboard is actually a general purpose control board that can be used in many other applications. The mainboard is fully soldered (except a few through-hole components) and factory tested before packing.
The DSO Shell comes with full enclosure. The front panel and the top/bottom brackets are flexible to allow easy user modification.
A rotary encoder has been added to the design as well. This allows parameter adjustment to be much quicker and easier.
The resolution of the DSO Shell has been extended from that of the DSO138. It reaches 5mV/div - 20V/div while DSO138 was only capable of 10mV/div - 5V/div. This allows for much wider measurements to be viewed and extend the applications for the DSO Shell.
DSO Shell kits has all SMD parts on the analog board pre-soldered and leaves through-hole parts for user to install.
DSO Shell runs on a 9V (do not use power voltage higher than 10V!) power supply. Users need to prepare their own power supply as it is not included in the kits. The power jack on the mainboard accepts standard 5.5mm/2.1mm DC plug. Alternative 2-pin connector (0.1"pitch) is also provided for convenience to connect to different power sources.
Note (Important)
It is assumed that users have adequate soldering and troubleshooting skills to assemble the DSO Shell kits. Buyers should be advised that due to the nature of this kit we can guarantee the fully assembled product will function; however, we will make as much efforts as we can to reach that goal.
After receiving the kits users are urged to check the mainboard and LCD by applying a proper power supply. Report immediately to your seller or JYE Tech if a problem or damage is found.
For the 15003K kit SMD component soldering skills are required. SMD parts should be installed before all other through-hole parts.
Weight | G.W 180g |
Battery | Exclude |
Vertical | |
Number of Channel | 1 |
Analog Bandwidth | 0 - 200KHz |
Sensitivity | 5mV/Div - 20V/Div |
Sensitivity error | < 5% |
Resolution | 12-bit |
Input Impedance | 1M ohm |
Maximum Input voltage | 50Vpk |
Coupling | DC, AC, GND |
Horizontal | |
Max Real-time Sampling Rate | 1Msps |
Timebase | 10us/Div - 500s/Div |
Record Length | 1024 |
Trigger | |
Trigger Modes | Auto, Normal, Single |
Trigger Types | Rising/falling edge |
Trigger Position | 1/2 of buffer size fixed |
Display | |
LCD Display | 2.4-inch color TFT LCD with 320 x 240 resolution |
Power Supply | |
Voltage | 9V DC (8 - 10V acceptable) |
Supply Current | 120mA @ 9V |
Physical | |
Dimension | 115mm X 75mm X 22mm |
Weight | 100 gram (not including cables and power supply) |
DSO Shell kit with SMD parts on analog board pre-soldered | 1 |
BNC-clip cable | 1 |
User Manual (English) | 1 |
DSO Shell是一套0-200 KHz帶寬示波器,具有結構,機械和操作的改進。
顯示器和MCU現在安裝在同一個板(主板)上,以避免使用板間引腳。來自DSO138的反饋表明,針頭上的焊接對於許多初學者來說常常是有問題的。模擬通道放置在包含大多數用戶安裝部件的分離板上。這樣可以在模擬和數字電路之間實現更好的分離。沒有模擬部分,主板實際上是可用於許多其他應用的通用控制板。主板已完全安裝(除了幾個貫通部件),並在包裝前經過工廠測試。
DSO Shell配有全機箱。前面板和頂部/底部支架是可彎曲的,便於用戶修改。
已添加旋轉編碼器。它使參數調整更快更容易。
DSO Shell的靈敏度已經在雙向上得到了擴展,並且比DSO138更高和更廣。它達到5mV / div --- 20V / div,而DSO138只有10mV / div --- 5V / div。
DSO Shell套件有兩種配置:15001K和15002K。它們之間的區別主要在模擬板上。 15001K在模擬板上預先焊接所有SMD部件,並留下通孔部件供用戶安裝。 15002K沒有預先焊接的零件。模擬板上的所有組件(包括SMD)由用戶安裝。
DSO Shell運行在9V(不要使用高於10V的電源電壓)電源。用戶需要準備自己的電源,因為它不包括在套件中。主板上的電源插孔接受5.5mm / 2.1mm直流插頭。還提供了另外的2針連接器(0.1“間距),方便連接到不同的電源。
重要筆記
•假設用戶具有adaquate焊接技巧和故障排除技巧來組裝DSO Shell套件。 建議買家由於使用者的技能參與裝配,不能保證每個套件都將成為一個工作裝置。但是我們將盡可能多地努力實現這一目標。
•接收到工具包後,請用戶通過正確的電源檢查主板和LCD。如果發現問題或損壞,立即向您的賣家或JYE Tech報告。
•對於15003K套件,需要SMD組件焊接技術。所有其他通孔部件之前應安裝SMD零件。