進口程序準備中,近期開放購買。

注意:目前價格僅供參考。

SparkFun迷你GPS盾

原名
SparkFun Mini GPS Shield

貨號
GPS-14030

特價
427

資料來源:https://www.sparkfun.com/products/14030

The SparkFun Mini GPS Shield equips your Arduino Mini with access to a GPS module, µSD memory card socket and all of the other peripherals you’ll need to turn your Arduino into a position-tracking, speed-monitoring, altitude-observing wonder logger. The shield is based around the GP-735 GPS module, a 56-channel GPS receiver featuring a uBlox 7th generation chip set and an up to 10Hz update rate. The board also uses a level shifter, so there’s no need to worry about the logic voltage of your Arduino Mini.

The Mini GPS Shield is a mini version of our GPS Logger Shield. While the GPS Logger Shield was designed to work with the Arduino RedBoard, the Mini GPS Shield was designed to work with the Arduino Mini/Micro boards.

The shield comes with a 6-pin JST connector to connect the GP-735 module. If you already have a GPS module, the JST pins are broken out and labeled to allow you to use just about any GPS module that works down to 3.3V. The Mini GPS Shield will work with any of our Arduino Mini boards. The board uses 3.3V logic; however, the logic level converter on the shield allows you to use 5V boards just as easily. The mini boards have symmetrical pins, which means it’s very easy to plug the shield in the wrong way. Plugging the shield in backward won’t damage either board, but it is something that could be easy to overlook. Make sure to check out the Hookup Guide below for proper installation instructions.

Get Started with the Mini GPS Shield Guide

Features:

  • Supports GP-735 with pins broken out to support most 3.3V tolerant GPS modules
  • Supports backup battery options
  • uSD memory card socket
  • Works with any Arduino Mini board (3.3V or 5V)
  • UART switch controls serial communications
  • Configurable LED to show GPS fix

Documents:

Videos

在SparkFun迷你GPS裝備盾的Arduino的迷你,可使用GPS模塊,μSD存儲卡插槽和所有你需要把你的Arduino到位置跟踪,速度監測,高空觀測記錄難怪其他外設。屏蔽是基於各地GP-735 GPS模塊,56通道GPS接收器配備了UBLOX第7代芯片組和一個上到10Hz刷新率。該主板還採用了電平轉換器,所以沒有必要擔心你的Arduino Mini的邏輯電壓。

迷你GPS盾是我們的迷你版GPS記錄器盾 。而GPS記錄器屏蔽設計與Arduino的RedBoard工作,迷你GPS屏蔽罩的設計與Arduino的小型/微型板工作。

屏蔽帶有一個6針JST連接器連接GP-735模塊。如果你已經擁有了GPS模塊,JST引腳爆發和標籤,讓您使用幾乎任何GPS模塊的工作原理降低到3.3V。迷你GPS屏蔽罩將與任何我們的Arduino迷你板工作。該板採用3.3V邏輯;然而,在屏蔽邏輯電平轉換器可以讓你很容易地使用5V板。迷你主板有對稱的引腳,這意味著它很容易堵塞盾在錯誤的道路。在落後堵漏罩不會損壞任何一塊板,但它是有可能很容易被忽視。確保檢查出聯播指南下面的正確安裝說明。

開始使用迷你GPS盾指南

特徵:

  • 支持GP-735與銷突破至支持大多數3.3V寬容的GPS模塊
  • 支持備用電池選項
  • USD記憶卡插槽
  • 與任何的Arduino迷你板(3.3V或5V)作品
  • UART開關控制的串行通信
  • 配置LED顯示GPS定位

文件:

前往
現貨型錄

Line share