進口程序準備中,近期開放購買。

注意:目前價格僅供參考。

SparkFun GPS記錄器盾

原名
SparkFun GPS Logger Shield

貨號
GPS-13750

特價
1,483

資料來源:https://www.sparkfun.com/products/13750

The SparkFun GPS Logger Shield equips your Arduino with access to a GPS module, µSD memory card socket, and all of the other peripherals you’ll need to turn your Arduino into a position-tracking, speed-monitoring, altitude-observing wonder logger. The shield is based around a GP3906-TLP GPS Module – a 66-channel GPS receiver featuring a MediaTek MT3339 architecture and up to a 10Hz update rate. The GPS module will stream constant position updates over a simple TTL-level serial port, which you can then log to a µSD card and/or use for other purposes.

Everything on the shield is highly configurable: A switch allows you to select the GPS module’s UART interface between either hardware or software ports, the µSD card operates over a hardware SPI port, which should be compatible with most Arduino layouts, and extra prototyping space should allow you to add those last, few components you need to complete your project. The GPS Logger Shield’s main voltage supply is taken from the Arduino 5V header pin. This voltage is regulated down to 3.3V, which is supplied to both the GPS module and the µSD card. These two components should consume, about 30mA on average, but they may very occasionally spike to around 100mA. We also highly recommend a 12mm Coin Cell Battery, which fits into the GPS Shield’s battery holder.

Note: The shield does not come with headers installed; we recommend the Arduino Stackable Header Kit.

Features:

  • On-Board GP3906-TLP GPS Module
  • 12mm Coin cell battery socket
  • µSD memory card socket
  • Standard Arduino sized shield
  • Prototyping area
  • GPS Module Pins Broken Out
  • Arduino reset button
  • UART switch controls serial communications

Documents:

在SparkFun GPS記錄器裝備盾的Arduino您可以訪問一個GPS模塊,μSD存儲卡插槽,以及所有你需要把你的Arduino到位置跟踪,速度監測,高空觀測記錄難怪其他外設。屏蔽是基於一個GP3906-GPS TLP模塊 - 一個66通道的GPS接收器配備了聯發科MT3339架構和高達在10Hz刷新率。 GPS模塊將流式播放網上一個簡單的TTL電平的串行端口固定位置的更新,然後您可以登錄到μSD卡和/或用於其他目的。

上盾一切都是高度可配置的:一個開關,您可以選擇硬件或軟件端口之間的GPS模塊的UART接口,μSD卡工作在硬件SPI端口,這應該是與大多數Arduino的佈局兼容,和額外的原型設計空間應允許您添加您需要完成項目的最後幾個元件。該GPS記錄器屏蔽的主電源電壓從5V Arduino的腳頭拍攝。該電壓被調節至3.3V,這同時提供給GPS模塊和μSD卡。這兩個組件要消耗大約平均30mA時,但他們很可能偶爾會秒殺到大概捐助。我們也強烈建議一個12毫米鈕扣電池 ,其中融入了GPS盾的電池盒。

注意:盾不附帶安裝頭;我們推薦的Arduino可堆疊頭套件

特徵:

  • 板載GP3906-TLP GPS模塊
  • 12毫米鈕扣電池插座
  • μSD記憶卡插槽
  • 標準的Arduino大小盾牌
  • 原型設計區域
  • GPS模塊引腳爆發
  • Arduino的復位按鈕
  • UART開關控制的串行通信

文件:

前往
現貨型錄

Line share