進口程序準備中，近期開放購買。
注意：目前價格僅供參考。
Arduino MKR1000（帶頭）
原名
Arduino MKR1000 (with Headers)
貨號
DEV-14393
特價
1,373
資料來源：https://www.sparkfun.com/products/14393
The Arduino MKR1000 is a powerful board that combines the functionality of an Arduino Zero and a handy WiFi shield. This thin board has been designed to offer a practical and cost-effective solution for makers wanting to design IoT projects with minimal previous experience in networking. It is based on the Atmel® ATSAMW25 SoC (System on Chip), which is part of the SmartConnect family of Atmel wireless devices specifically designed for Internet of Things (IoT).
The MKR1000 design includes a LiPo charging circuit that allows the Arduino to run on battery power or external 5V, charging the LiPo battery while running on external power. Switching from one source to the other is done automatically. A good 32-bit computational power similar to the Arduino Zero board, the usual rich set of I/O interfaces, low-power WiFi with a Cryptochip for secure communication, and the ease of use of the Arduino Integrated Development Environment (IDE) for code development and programming. All of these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power (5V) to the board. The Arduino MKR1000 is able to run with or without the LiPo battery connected and has limited power consumption.
Note: This version of the Arduino MKR1000 has labeled, stackable headers already mounted to the board. If you would like an MKR1000 without headers pre-mounted, purchase this version instead.
Features:
- Microcontroller: SAMD21 Cortex-M0+ 32-bit low-power ARM MCU
- Board Power Supply (USB/VIN): 5V
- Circuit Operating Voltage: 3.3V
- Digital I/O Pins: 8
- PWM Pins: 12
- Flash Memory: 256 KB
- SRAM: 32 KB
- Full-speed USB device and embedded host
- Pre-mounted headers with pin-out
Documents:
Videos
Arduino MKR1000是一個功能強大的電路板，結合了Arduino Zero和方便的WiFi屏蔽功能。這種薄型電路板的設計旨在為希望設計物聯網項目的製造商提供實用且經濟高效的解決方案，而這些項目的網絡使用經驗極少。它是基於愛特梅爾®ATSAMW25的SoC（片上系統），這是家庭的SmartConnect專門針對物聯網（IOT）的互聯網設計愛特梅爾無線設備的一部分。
MKR1000設計包括一個LiPo充電電路，允許Arduino使用電池電源或外部5V電源運行，在外部電源上運行時為LiPo電池充電。從一個源切換到另一個是自動完成的。一個很好的32位計算能力，類似於Arduino Zero電路板，通常豐富的I / O接口，帶Cryptochip的低功耗Wi-Fi安全通信以及Arduino集成開發環境（IDE）的易用性代碼開發和編程。所有這些功能都使這款主板成為緊湊型新興IoT電池供電項目的首選。 USB端口可用於為電路板提供電源（5V）。 Arduino MKR1000可連接或不連接LiPo電池，功耗有限。
注意：這個版本的Arduino MKR1000已經安裝了可標記的可堆疊接頭。如果您希望MKR1000沒有預裝接頭，請購買此版本 。
特徵：
- 微控制器：SAMD21 Cortex-M0 + 32位低功耗ARM MCU
- 板電源（USB / VIN）：5V
- 電路工作電壓：3.3V
- 數字I / O引腳：8
- PWM引腳：12
- 閃存：256 KB
- SRAM：32 KB
- 全速USB設備和嵌入式主機
- 預安裝標頭與引腳
文件：
