TOL107C3M Digital Storage Oscilloscope DIY Kit with

原名

貨號

TOL107C3M

分類

Accessories for Ham Radio & Instruments

特價

商品停售

由於停止生產、銷量不佳、升級改版... 或其他因素，SeeedStudio 原廠目前已經停止生產、供應、或銷售本件商品，請尋找其他替代品方案。

資料來源：https://www.seeedstudio.com/Digital-Storage-Oscilloscope-DIY-Kit-with-Panels-p-515.html

Description

Read this first:

Before you buy this KIT, make sure you have enough DIY ability to finish it. We will provide as much help as we can if you need, but we won't guarantee the replacement unless the problem is caused by failure parts.

People talked about an oscilloscope for DIYers, that’show we know about JYE tech. Mr. Liu is an admirable experiencedengineer, being the first generation of university EE student afterculture revolution. His seriousness on documents and every detailamazed me. You will find complete document on their website, includingdemos and assemle guide. We are honored to carry their products, neatand handy for Arduino level electrical development.

Assembled view

Kit includes:

1 ) All parts (excluding power adapter)

2 ) Schematic

3 ) Assembly Notes

4 ) Operatiing instructions

5 ) MCU (ATmega64) has been pre-soldered and programmed

[ Note: SMD soldering skills are required for 06201KP. Fortunately there are plenty of sites that teach these skills. Simply search with"SMD soldering"you will find lots of them. ]

Features:

* Max sample rate - 5M/s (AUTO mode)，8 bits

* Sample memory depth - 256 bytes

* Analog bandwidth - 1MHz

* Vertical sensitivity - 100mV/Div - 5V/Div

* Vertical position adjustable with indicator

* Input impedance - 1MΩ

* Max input voltage - 50Vpp

* DC/AC coupling

* Horizontal - 2μs/Div - 10m(minute)/Div

* Auto, normal and single trig modes

* Rising/falling edge trigger

* External trig available

* Trig level adjustable with indicator

* Hold/run feature

* Save up to 6 captures to EEPROM and retain after power down

* Retrieve and display saved captures

* Transfer its screen to PC as bitmap file via serial connection

* Built-in 500Hz/5Vpp test signal

* Frequency counter (only for TTL level input signal)

* 9 DC power supply

* Dimension: 110mm X 65mm X 25mm (without case)

Resources:

Operating Instructions [v05]

How to Program the Scope with Programmer or Bootloader

Firmware

PC program for downloading codes via the bootloader

How to Use the External Trigger

描述

閱讀這首：

在您購買此套件，請確保您必須完成它足夠的DIY能力。因為我們可以，如果你需要，我們將提供盡可能多的幫助，但我們不能保證更換，除非該問題是由故障引起的部分。

人們談論了DIYers的示波器 ，這就是我們如何知道捷科技。劉先生是一個令人欽佩的經驗的工程師，是文革後第一代大學電子工程的學生。他在文件和每一個細節都認真讓我吃驚。你會發現在其網站上完整的文檔，包括演示和裝配自動引導。我們很榮幸能夠隨身攜帶自己的產品，整潔和方便的Arduino的水平電器的發展。

裝配圖

套件包括：

1）所有部件（不包括電源適配器）

2）示意圖

3）注意事項大會

4）Operatiing說明

5）的MCU（ATmega64的）已被預先焊接和編程

[注：SMD的焊接技能都需要06201KP。幸運的是有很多，教這些技能的網站。簡單地用“貼片焊接”搜索，你會發現很多很多。 ]

特徵：

*最大採樣率- 5M /秒（自動模式），8位

*樣品的存儲深度- 256字節

*模擬帶寬- 1MHz的

*垂直靈敏度-為100mV /格- 5V /格

*垂直位置可調帶指示燈

*輸入阻抗- 1MΩ

*最大輸入電壓- 50Vpp

* DC / AC耦合

*水平-為2μs/格萬- 1000萬（分鐘）/格

*自動，正常和單次觸發模式

*上升/下降沿觸發

*外部trig的可用

*觸發電平調節帶指示燈

*保持/運行功能

*節省高達6捕捉到EEPROM和斷電後保留

*檢索和顯示保存捕捉

*通過串行連接傳輸其屏幕PC作為位圖文件

*內置500Hz的/ 5VPP測試信號

*頻率計數器（僅適用於TTL電平輸入信號）

* 9直流電源

*尺寸：110毫米點¯x65毫米x 25mm的（不區分）

資源：

固件