資料來源:https://www.seeedstudio.com/M328W---wireless-Internet-of-Things-module-p-2323.html
We are sorry M32W is discontinued. We use M328W to replace M32W. (M328W Datasheet)
M32W wireless Internet of Things module is designed for the easy of programming and installation for IoT projects where wireless protocol (zigbee, bluetooth, 433Mhz etc) is required. It is a plug-in module for MS14 and powered by an ATMEL ATmega32u4 micro-controller.
The M32W has a standard XBEE Socket and RFM12B footprint to implement different wireless protocol modules. It also has a breadboard area for easy prototyping.
M32W is Arduino Yun compatible. It can be programmed and debug by the Arduino IDE(ver 1.5.4 or later) via WiFi.
With the combination of MS14, M32W and Arduino Yun software, user can install / prototype Internet of Things projects in an easy / rapidly way.
Features
Bridge various wireless protocols such as zigbee, bluetooth, NFC into WiFi IP network.
Internet of Things Gateway module to connect sensor network to internet.
Log sensor data and upload to remote server.
Control switch/relay from Internet.
Arduino IDE compatible, can be programmed /debug by Arduino IDE.
Program/update/ debug via WiFi network.
Specifications
Microcontroller: ATmega32u4
Operating Voltage: 3.3V
I/O voltage: 3.3V
SRAM: 2.5KB
Flash Memory: 32KB (of which 4KB used by bootloader)
EEEPROM: 1KB
Clock Speed: 16Mhz
Digital I/O pins: 15
Analog input channels: 6
PWM channels: 4
BEE Socket: 1
ESD-protection: IEC 61000-4-2
Over Voltage Protect
XBee Socket | M32W has a standard XBee Socket. Any module compatible with this socket can be used directly in M32W. | |
RFM12B footprint | RFM12B footprint for HopeRF RFM12B module or RFM69CW/HCW 433/868/915 Radio module. | |
Prototype Area | An on board prototype area with power and Arduino Pin out for easy prototyping. | |
Customized Screw Terminal | While M32W is used with MS14-S, user can define the screw terminal feature by using the prototype area as shown above. Which gives more flexible/ possibility for prototyping. | |
USB port debug /programming | M32W has a micro USB connector and can act as standard USB COM device. This USB connection can be used to upgrade sketch or debug the software via serial monitor on Arduino IDE. |
Document
Technical detail and examples are in M32 WiKi Page
Schematic and pcb (pdf) (Eagle version)
For any technical support or suggestion, please kindly go to ourforum.
Dimensions | 80mm x 90mm x 10.6mm |
Weight | G.W 18g |
Battery | Exclude |
對不起, M32W 已經停產了。我們用 M328W 來代替 M32W。(M328W 資料表)
M32W 無線互聯網的東西模組設計為易於程式設計和安裝的專案, 其中無線協定 (zigbee, 藍牙, 433Mhz 等) 是必需的。它是 MS14的外掛程式模組, 並由 ATMEL ATmega32u4 微控制器提供電源.
M32W 有一個標準的 XBEE 插座和 RFM12B 足跡來實現不同的無線協定模組。它也有一個板的領域, 易於原型。
M32W 是Arduino 雲相容。它可以由 Arduino IDE (1.5.4 或更高版本) 通過 WiFi 進行程式設計和調試.
與的組合MS14, M32W 和Arduino 雲軟體, 使用者可以簡單/快速地安裝/原型的東西專案的互聯網.
功能
將各種無線協定 (如 zigbee、藍牙、NFC) 橋接到 WiFi IP 網路中。
互聯網的東西閘道模組連接感應器網路到互聯網。
記錄感應器資料並上載到遠端伺服器。
控制開關/繼電器從互聯網。
Arduino ide 相容, 可通過 Arduino ide 進行程式設計/調試。
通過 WiFi 網路進行程式/更新/調試。
規格
微控制器: ATmega32u4
工作電壓: 3.3V
i/o 電壓: 3.3V
SRAM: 2.5KB
快閃記憶體: 32KB (其中4KB 由引導載入程式使用)
EEEPROM: 1KB
時脈速度: 16Mhz
數位 i/o 針腳:15
類比輸入通道: 6
PWM 通道: 4
蜂插座: 1
ESD 保護: IEC 61000-4-2
過電壓保護
XBee 插座 | M32W 有一個標準的 XBee 插座。與此插座相容的任何模組都可以直接在 M32W 中使用。 | |
RFM12B 足跡 | RFM12B 的足跡為 HopeRF RFM12B 模組或 RFM69CW/HCW 433/868/915 無線電模組。 | |
原型區域 | 一個在板上的原型區與電源和 Arduino 引腳, 易於原型。 | |
定制螺絲端子 | 當 M32W 與 MS14-S 一起使用時, 使用者可以使用上面所示的原型區域來定義螺釘終端的特徵。它為原型提供了更靈活的可能性。 | |
USB 埠調試/程式設計 | M32W 有一個微型 usb 連接器, 可以充當標準的 usb COM 設備。此 USB 連接可用於在 Arduino IDE 上通過串列監視器升級草圖或調試軟體。 |
文檔
技術詳細資訊和示例在 M32 WiKi 頁
對於任何技術支援或建議, 請轉到我們的論壇.
尺寸 | 80mm x 90mm x 10.6mm |
重量 | G. W 18g |
電池 | 排除 |