資料來源:https://www.seeedstudio.com/IOT-Dev-Kit-for-Mbed-%28Delta-DFBM-NQ620-EVB%29-p-2790.html
This kit contains an ARM mbed compatible HDK mother board and a daughter board mounted with CE/FCC/TELEC and Bluetooth EPL certified BLE module. The mother board is designed to compatible with I2S, Arduino Uno Revision 3 standard so various 3rd-party audio, sensing, control capability shields can interface with BLE with NFC Tag module for rapid prototyping BLE applications. NQ620 support Bluetooth LE 4.2 to 5.X software devices stack.
The NQ620 module is based on NORDICSemi nRF52832 SoC therefore it supports the standard Nordic Software Development local compiler using Keil, IAR and GCC as well as ARM mbed online compiler for embedded standalone application development. The module also supports Delta defined BLE CLI (Command Line Interface) which allow external host MCU to control and set BLE communication through UART. The CLI running on the module handles all the BLE protocol tasks ends up the application is left to be implemented on external host MCU with minimal development overhead.
What’s more, BLE 5.0 will be available if you upgrade the firmware and SDK, though so far we are not able to support in extended range, you may still benefit from twice the transmission speed of Bluetooth v4.2.
Delta DFBM-NQ620 BLE module daughter board
NORDICSemi nRF52832 with ARM® Cortex®-M4F processor
I2S audio interface for audio codec
32MHz embedded crystal, 32.768KHz embedded RTC
512KB flash memory, 64KB SRAM,
Additional 512KB SPI flash for application data storage
On board chip antennae for BLE and NFC tag
CE/FCC/TELEC and BLUETOOTH EPL certified
Delta DFBM-NQ620 mother board
USB drag and drop programming
USB Virtual COM port for serial terminal
CMSIS-DAP interface for programming and debugging
Accepts power through USB or external source (7V-12V)
Pin header for current measurement
Cortex-M4F with I2S Audio I/F
CE/FCC/TELEC with Bluetooth LE EPL
Arduino compatible
Schematic Diagram
1 x Delta DFBM-NQ620-XE0R (HDK mother board)
1 x Delta DFXE-SM001-DT0R (BLE Module)
For technical discussion, please post them on mbed forum.
For projects that you would like to share with the community, please visit Recipe.
該套件包含一個ARM mbed兼容HDK母板和子板安裝有CE / FCC / TELEC和藍牙認證的EPL BLE模塊。該主板設計為兼容I2S,Arduino的烏諾修訂3標準的各種這樣的第三方音頻,傳感,控制能力盾可與快速成型應用BLE NFC標籤模塊BLE接口。 NQ620支持藍牙4.2 LE到5.x軟件的設備堆棧。
該NQ620模塊基於NORDICSemi nRF52832系統芯片,因此它支持採用Keil,IAR和GCC為嵌入式獨立的應用程序開發標準的北歐軟件開發本地編譯以及ARM mbed在線編譯器。該模塊還支持三角洲定義BLE CLI(命令行界面),它允許外部主機MCU來控制,並通過UART設置BLE通信。該模塊上運行的CLI處理所有的BLE協議任務結束應用程序已被外部主機MCU實現以最小的開發開銷。
更重要的是,BLE 5.0將可如果升級固件和SDK,但到目前為止,我們無法在擴展範圍的支持,您仍然可以從兩次藍牙V4.2傳輸速度中獲益。
三角洲DFBM-NQ620 BLE模塊子板
NORDICSemi nRF52832與ARM®Cortex®-M4F處理器
I2S音頻接口,音頻編解碼器
32MHz的內嵌晶體,32.768kHz的嵌入式RTC
512KB閃存,64KB SRAM,
附加512KB SPI閃存應用數據存儲
在板載芯片天線的BLE和NFC標籤
CE / FCC / TELEC和藍牙認證的EPL
三角洲DFBM-NQ620主板
USB拖放編程
USB虛擬COM端口用於串行終端
CMSIS-DAP接口進行編程和調試
通過USB或外部電源供電接受(7V-12V)
排針用於電流測量
的Cortex-M4F與I2S音頻I / F
CE / FCC /帶藍牙LE EPL TELEC
Arduino的兼容
原理圖,示意圖
1個三角洲DFBM-NQ620-XE0R(HDK主板)
1個三角洲DFXE-SM001-DT0R(BLE模塊)
關於技術的討論,請發布到 mbed論壇 。
對於您希望與社區分享的項目,請訪問配方 。