資料來源:https://www.seeedstudio.com/Arduino-Adapter-For-Raspberry-Pi-p-2443.html
Arduino is a massive ecosystem, if there's a way for the Raspberry Pi GPIO interface to adapt to Arduino pinouts, it is possible to use the Pi together with vast Arduino shields and hardware/software resources. The ARPI600 is just intended for this.
What's more, the ARPI600 also support XBee modules, make it easy to add wireless feature to your great project.
Supported Pi:
Raspberry Pi 1 Model A+
Raspberry Pi 1 Model B+
Raspberry Pi 2 Model B
FEATURES
Compatible with Arduino UNO, Leonardo, easy to connect with various Arduino shields
XBee connector for connecting various XBee modules
Sensor interface for connecting various sensors
Onboard USB TO UART for serial port debugging, also can be configured as XBee USB adapter
Onboard ADC, 10 bit, 38KSPS, 11 channels (6 channels for Arduino interface, 5 channels for sensors)
Onboard RTC
SPECIFICATION
1.Arduino connector : for connecting Arduino shields
2.ICSP interface : Arduino ICSP
3.XBee connector : for connecting XBee communication modules
4.Sensor interface : for connecting sensors
5.Raspberry Pi connector : for connecting Raspberry Pi
6.USB TO UART
7.TLC1543 : AD converter
8.PCF8563 : RTC
9.CP2102
10.32.768KHz crystal : for RTC
11.Power indicator
12.XBee state LED
13.XBee and Arduino interface RESET button
14.XBee EASYLINK button
15.RTC battery holder : for CR1220 button battery
16.TLC1543 reference voltage configuration jumper
17.RTC jumper
18.UART jumper
when connecting P_RX and CP_TX, P_TX and CP_RX respectively, USB TO UART is connected to Raspberry Pi serial port
when connecting XB_RX and CP_TX, XB_TX and CP_RX respectively, USB TO UART is connected to XBee serial port
when connecting XB_RX and P_TX, XB_TX and P_RX respectively, Raspberry Pi serial port is connected to XBee serial port
19.Arduino AD selection jumper
short 2 and 3 : Arduino A0-A5 as AD input
short 1 and 2 : Arduino A0-A5 as digital control
20.Arduino I2C selection jumper
short the jumper : Arduino A4-A5 as I2C control (the A4-A5 of Arduino AD selection jumper should be opened)
21.Arduino SPI selection jumper
short 1 and 2 : Arduino D11-D13 as SPI control (default)
short 2 and 3 : Arduino D11-D13 as digital control
DOCUMENTS
Please visit wiki page for more info about this product.
For technical support, please post your questions to our forum
Dimensions | 150mm x 105mm x 29mm |
Weight | G.W 101g |
Battery | Exclude |
Arduino 是一個巨大的生態系統, 如果有一種方式為覆盆子 pi GPIO 介面, 以適應 Arduino 線, 它可以使用 Pi 與巨大的 Arduino 盾牌和硬體/軟體資源。ARPI600 只是為了這個
更重要的是, ARPI600 還支援 XBee 模組, 使您可以輕鬆地將無線功能添加到您的偉大專案中。
支援的 Pi:
覆盆子 Pi 1 模型 A +
覆盆子 Pi 1 模型 B +
覆盆子 Pi 2 模型 B
功能
與 Arduino 相容, 萊昂納多, 易於連接各種 Arduino 盾
用於連接各種 XBee 模組的 XBee 連接器
用於連接各種感應器的感應器介面
板載 usb 到 UART 串口調試, 也可配置為 XBee usb 配接器
板載 ADC, 10 位, 38KSPS, 11 通道 (6 通道用於 Arduino 介面, 5 通道用於感應器)
車載 RTC
規範
1.Arduino 連接器: 用於連接 Arduino 護盾
2.ICSP 介面: Arduino ICSP
3.XBee 連接器: 用於連接 XBee 通信模組
4.Sensor 介面: 用於連接感應器
5.Raspberry pi 連接器: 用於連接覆盆子 pi
6.USB 到 UART
7. TLC1543: AD 轉換器
8. PCF8563: RTC
9. CP2102
10.32.768KHz 水晶: 為 RTC
11.Power 指示器
12.XBee 狀態指示燈
13.XBee 和 Arduino 介面重定按鈕
14.XBee EASYLINK 按鈕
15.RTC 電池支架: 用於 CR1220 按鈕電池
16. TLC1543 參考電壓配置跳線
17.RTC 跳線
18.UART 跳線
當連接 P_RX 和 CP_TX, P_TX 和 CP_RX 分別, USB 到 UART 連接到覆盆子 Pi 序列埠
連接 XB_RX 和 CP_TX、XB_TX 和 CP_RX 時, USB 到 UART 連接到 XBee 序列埠
當連接 XB_RX 和 P_TX, XB_TX 和 P_RX 分別, 覆盆子 Pi 串口連接到 XBee 序列埠
19.Arduino 廣告選擇跳線
短2和 3: Arduino A0-A5 作為 AD 輸入
短1和 2: Arduino A0-A5 作為數位控制
20.Arduino I2C 選擇跳線
短跳線: Arduino A4-A5 作為 I2C 控制 (A4-A5 Arduino AD 選擇跳線應打開)
21.Arduino SPI 選擇跳線
短1和 2: Arduino D11-D13 作為 SPI 控制 (預設)
短2和 3: Arduino D11-D13 作為數位控制
檔
有關此產品的更多資訊, 請訪問wiki頁面。
有關技術支援, 請將您的問題張貼到我們的論壇
尺寸 | 150mm x 105mm x 29mm |
重量 | G. W 101g |
電池 | 排除 |