進口程序準備中，近期開放購買。
注意：目前價格僅供參考。
SparkFun同時RFID閱讀器 - 納米M6E
原名
SparkFun Simultaneous RFID Reader - M6E Nano
貨號
SEN-14066
特價
6,598
資料來源：https://www.sparkfun.com/products/14066
The SparkFun Simultaneous RFID Reader is an Arduino-compatible board to get you started with the M6E Nano UHF RFID Reader. Radio Frequency Identification (RFID) is becoming popular everywhere for tracking practically everything. Whether you want to get started by adding an RFID reader on your toolbox with tags on all your tools or allowing access to the tree house for your secret society meetings, this board may be for you!
With the Arduino shield footprint, you can connect this directly to an Arduino-compatible board, or a different microcontroller. You can also connect directly to your computer using the FTDI header on the board and read data using the Universal Reader Assistant.
Once you’ve started, this board will read EPCglobal Gen 2 tags (see Recommended Products) at up to 150 tags per second. Writing of tags is also possible at 80msec standard write. The board has adjustable power output from 0dBm to 27dBm, meaning that with the correct antenna you can read up to 16 feet (4.9m), or 1 to 2 feet with the onboard antenna.
Note: Your reader ships with a piece of gray, nonconductive Thermal Gap Filler to help with both heat dissipation and to cover the exposed ground plane (to prevent circuits from shorting against it).
Warning: Ensure that personnel do not stand in the radiation beam of the antenna unless they are more than 21cm away from the face of the antenna (to adhere to FCC limits for long-term exposure). See Datasheet for more information.
Get Started with the Simultaneous RFID Reader Guide
Features:
- EPCglobal Gen 2 (ISO 18000-6C) with nominal backscatter rate of 250kbps
- Separate read and write levels, command adjustable from 0dBm to 27dBm in 0.01 dB steps
- 0.84W in ready mode
- 0.00025W in shutdown mode
- Up to 150 tags/sec to read 96-bit EPC
- 80msec typical for standard write of 96-bit EPC
Documents:
- Schematic
- Eagle File
- RFID basics
- Hookup Guide
- Datasheet
- Design Guide
- Thermal Gap Filler
- Firmware Update (v1.9.0)
- Product Page
- Universal Reader Assistant 32-bit/64-bit (Windows only)
- GitHub (Design Files)
- GitHub (Arduino Library)
Videos
該SparkFun同時RFID閱讀器是一個Arduino兼容板，讓您開始與M6E納米UHF RFID閱讀器。無線射頻識別（RFID）是用於跟踪幾乎一切都變得越來越流行無處不在。無論你想獲得通過你的工具箱中添加RFID讀寫器與所有的工具標籤或允許訪問的樹屋為你的秘密社團會議開始，這款主板可能是你！
隨著Arduino的盾牌足跡，你可以直接連接到這一個Arduino兼容板，或不同的微控制器。您也可以直接使用主板上的FTDI頭連接到您的計算機並使用通用讀寫器助理讀取數據。
一旦你開始，這個委員會將在每秒150標籤閱讀EPCglobal的Gen 2標籤（見推薦產品）。標籤寫作也可以在80毫秒標準寫入。該板具有可調節的功率輸出從為0dBm到27dBm時，這意味著與正確的天線可以與車載天線讀取多達16英尺（4.9米），或1到2英尺。
注意：您的閱讀器附帶了一塊灰色的，不導電的熱填空發射機的，以幫助這兩個散熱性和覆蓋暴露的接地層（防止電路發生短路反對）。
警告：確保人員不天線的輻射光束站，除非它們是超過21厘米從天線的臉了（遵守FCC的限制長期暴露）。請參閱數據表以了解更多信息。
特徵：
- EPCglobal的第2代（ISO 18000-6C）與250kbps的標稱反向散射率
- 單獨的讀和寫的水平，以0.01 dB步進命令可調為0dBm到27dBm的
- 0.84W在就緒模式
- 0.00025W在關斷模式
- 高達150個標籤/秒讀96位EPC
- 80毫秒的典型96位EPC的標準寫入
文檔：
